Store Categories
Store Categories
XR2206 Function Signal Generator DIY Kit Sine Triangle Square Wave 1HZ-1MHZ US Details Features: These are all the parts, it need your own welding and installation Voltage Supply: 9-12V DC Input Waveforms: Square, Sine & Triangle Impedance: 600 Ohm + 10% Frequency: 1Hz - 1MHz SINE WAVE Amplitude: 0 - 3V at 9V DC input Distortion: Less than 1% (at 1kHz) Flatness: +0.05dB 1Hz - 100kHz SQUARE WAVE Amplitude: 8V (no load) at 9V DC input Rise Time: Less than 50ns (at 1kHz) Fall Time: Less than 30ns (at 1kHz) Symmetry: Less than 5% (at 1kHz) TRIANGLE WAVE Amplitude: 0 - 3V at 9V DC input Linearity: Less than 1% (up to 100kHz) 10mA 2. The Function Generator component parameter table Note label type parameters R1 resistor 1K Regardless of the polarity R2 Adjustable resistance B503=50K (by screen printing layer) R3, R5,R6 resistor 5.1K Regardless of the polarity R4 resistor 330 Regardless of the polarity R7 Adjustable resistance B503=50K (by screen printing layer) R8 Adjustable resistance B104=100K (by screen printing layer) C1, Electrolytic capacitor 100UF The positive short feet negative long feet C2 non-polar capacitors 104 Regardless of the polarity C3,C4 Electrolytic capacitor 10UF The positive short feet negative long feet C5 non-polar capacitors 105 Regardless of the polarity C6 non-polar capacitors 473 Regardless of the polarity C7 non-polar capacitors 222 Regardless of the polarity C8 non-polar capacitors 101 Regardless of the polarity U1 IC XR2206 (by screen printing layer) JK1 DC POWER (by screen printing layer) J1 2PIN Jumper cap XM2.54 Regardless of the polarity J2 2PIN Jumper cap XM2.54 Regardless of the polarity P1 Signal wire terminal (by screen printing layer) J3 2*5P Jumper cap 3.The welding installation considerations, follow these steps: 1. The components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc. 2.Welding IC socket, terminal blocks, finally power socket, adjustable potentiometer. 3.The back with a diagonal cutting pliers to cut short the pins as far as possible 4.Debugging steps: 1.After completion of welding on IC, XR2206, pay attention to the direction of IC, insert the might damage the chip! 2. check the IC whether against, such as anti please timely correction. 3. Insert the power supply, power supply for 5.5 * 2.1 port, inside outside is negative polarity. For 9-12 v power supply voltage. The waveform may not be stable for more than 12 v 5.Using the step: 1. J1 jumper cap plug in, SIN/TRI blue terminals output sine wave (note J1, J2 can only insert one of)| |2. J2 jumper cap plug in, SIN/TRI blue terminals output triangular wave (note J1, J2 can only insert one of) 3. SQU blue terminals output pulse 4. AMP : Sine wave, triangle wave amplitude adjustment 5. FINE : Frequency fine adjustment 6. Coarse : Frequency of coarse adjustment 6.Schematic diagram of Function Generator Package Included: 1 x XR2206 Function Signal Generator DIY Kits Sine Triangle Square Output 1HZ-1MHZ Shipping Policy Payment Method Returns Policy Shipping Policy Payment Method
This is the description of Payment Method.
Do not dismiss your dream.
To be without dream is to be without hope.
To be without hope is to be without purpose.
Do not run through your life so fast that you forget not only where you have been, but also where you are
going.
Life is not race, but a journey to be savored each step of the way. Returns Policy
This is the description of Returns Policy.
Do not dismiss your dream.
To be without dream is to be without hope.
To be without hope is to be without purpose.
Do not run through your life so fast that you forget not only where you have been, but also where you are
going.
Life is not race, but a journey to be savored each step of the way. Copyright©2017 DataCaciques
XR2206 Function Signal Generator DIY Kit Sine Triangle Square Wave 1HZ-1MHZ US Details Features: These are all the parts, it need your own welding and installation Voltage Supply: 9-12V DC Input Waveforms: Square, Sine & Triangle Impedance: 600 Ohm + 10% Frequency: 1Hz - 1MHz SINE WAVE Amplitude: 0 - 3V at 9V DC input Distortion: Less than 1% (at 1kHz) Flatness: +0.05dB 1Hz - 100kHz SQUARE WAVE Amplitude: 8V (no load) at 9V DC input Rise Time: Less than 50ns (at 1kHz) Fall Time: Less than 30ns (at 1kHz) Symmetry: Less than 5% (at 1kHz) TRIANGLE WAVE Amplitude: 0 - 3V at 9V DC input Linearity: Less than 1% (up to 100kHz) 10mA 2. The Function Generator component parameter table Note label type parameters R1 resistor 1K Regardless of the polarity R2 Adjustable resistance B503=50K (by screen printing layer) R3, R5,R6 resistor 5.1K Regardless of the polarity R4 resistor 330 Regardless of the polarity R7 Adjustable resistance B503=50K (by screen printing layer) R8 Adjustable resistance B104=100K (by screen printing layer) C1, Electrolytic capacitor 100UF The positive short feet negative long feet C2 non-polar capacitors 104 Regardless of the polarity C3,C4 Electrolytic capacitor 10UF The positive short feet negative long feet C5 non-polar capacitors 105 Regardless of the polarity C6 non-polar capacitors 473 Regardless of the polarity C7 non-polar capacitors 222 Regardless of the polarity C8 non-polar capacitors 101 Regardless of the polarity U1 IC XR2206 (by screen printing layer) JK1 DC POWER (by screen printing layer) J1 2PIN Jumper cap XM2.54 Regardless of the polarity J2 2PIN Jumper cap XM2.54 Regardless of the polarity P1 Signal wire terminal (by screen printing layer) J3 2*5P Jumper cap 3.The welding installation considerations, follow these steps: 1. The components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc. 2.Welding IC socket, terminal blocks, finally power socket, adjustable potentiometer. 3.The back with a diagonal cutting pliers to cut short the pins as far as possible 4.Debugging steps: 1.After completion of welding on IC, XR2206, pay attention to the direction of IC, insert the might damage the chip! 2. check the IC whether against, such as anti please timely correction. 3. Insert the power supply, power supply for 5.5 * 2.1 port, inside outside is negative polarity. For 9-12 v power supply voltage. The waveform may not be stable for more than 12 v 5.Using the step: 1. J1 jumper cap plug in, SIN/TRI blue terminals output sine wave (note J1, J2 can only insert one of)| |2. J2 jumper cap plug in, SIN/TRI blue terminals output triangular wave (note J1, J2 can only insert one of) 3. SQU blue terminals output pulse 4. AMP : Sine wave, triangle wave amplitude adjustment 5. FINE : Frequency fine adjustment 6. Coarse : Frequency of coarse adjustment 6.Schematic diagram of Function Generator Package Included: 1 x XR2206 Function Signal Generator DIY Kits Sine Triangle Square Output 1HZ-1MHZ Shipping Policy Payment Method Returns Policy Shipping Policy 1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand. 2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders. 3.All package need to wait 30 days , Please take care it.Less than 30 days,we can't take a refund . Payment Method 1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase. 2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances. 3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country. Returns Policy 1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase. 2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse. 3. Please include your eBay ID and item number with any email requests.
Returns Accepted for this item if it's within 30 Days